4 Ways To Avoid Common Faults Of Worm Gear Reducer
Common faults of worm gear reducer
1. The reducer heats up and leaks oil. In order to improve efficiency, worm gear reducers generally use non-ferrous metals as worm wheels, and worms use harder steel. Because it is a sliding friction drive, a lot of heat will be generated during operation, which will cause differences in thermal expansion between the various parts of the reducer and the seal, thereby forming gaps in each mating surface, and the lubricating oil will become thinner due to the increase in temperature, which is easy to cause leakage .
There are four main reasons for this situation. One is the unreasonable combination of materials; the second is the poor quality of the friction surface; the third is the incorrect selection of the amount of lubricant; the fourth is the poor assembly quality and use environment.
2.Worm gear wear. The worm wheel is generally made of tin bronze, and the matched worm material is hardened with 45 steel to hrc4555, or 40cr hardened hrc5055, and then ground to a roughness of ra0.8μm by a worm grinder. The reducer wears very slowly during normal operation, and some reducers can be used for more than 10 years. If the wear rate is fast, it is necessary to consider whether the selection is correct, whether it is overloaded, and the material, assembly quality or use environment of the worm gear.
3.The drive pinion helical gear is worn. It usually occurs on the reducer installed vertically, mainly related to the amount of lubricating oil added and the type of oil. When installed vertically, it is easy to cause insufficient lubricating oil. When the worm gear reducer stops running, the transmission gear oil between the motor and the reducer is lost, and the gears cannot get the proper lubrication protection. When the reducer is started, the gears are not effectively lubricated, causing mechanical wear and even damage.
4. Worm bearing is damaged. When a failure occurs, even if the gearbox is well sealed, it is often found that the gear oil in the reducer is emulsified, and the bearings are rusted, corroded, and damaged. This is because the condensate produced by the gear oil temperature rises and cools down after the gearbox has been running for a period of time is mixed with water. Of course, it is also closely related to the quality of the bearing and the assembly process.
Trouble shooting method of worm gear reducer
1. Ensure assembly quality. Some special tools can be purchased or made by yourself. When disassembling and installing the reducer components, try to avoid hitting with other tools such as hammers; when replacing gears and worm gears, try to use original parts and replace them in pairs; when assembling the output shaft, pay attention Tolerance matching; anti-sticking agent or red lead oil should be used to protect the hollow shaft to prevent wear, rust, or dirt on the mating area, which is difficult to disassemble during maintenance.
2. Selection of lubricating oil and additives. Worm gear reducers generally use 220# gear oil. For worm gear reducers with heavy loads, frequent starts, and poor use environments, some lubricating oil additives can be used to make the gear oil still adhere to the gear surface when the reducer is stopped. A protective film is formed to prevent heavy load, low speed, high torque, and direct contact between metals when starting. The additives contain seal ring regulator and anti-leakage agent to keep the seal ring soft and elastic and effectively reduce lubricating oil leakage.
3. The selection of the installation position of the worm gear reducer. Where the location permits, try not to use vertical installation. In vertical installation, the amount of lubricating oil added is much more than that in horizontal installation, which may cause heat generation and oil leakage of the reducer.
4. Establish a good lubrication maintenance system. The reducer can be maintained according to the “five fixed” principle of lubrication work, so that every reducer has a person responsible for regular inspections, and it is found that the temperature rise is obvious, if the temperature exceeds 40 ℃ or the oil temperature exceeds 80 ℃, the quality of the oil decreases or the oil If you find too much copper powder and produce abnormal noise, you should stop using it immediately, check and repair it in time, eliminate the fault, and replace the lubricating oil. When refueling, pay attention to the amount of oil to ensure that the worm gear reducer is properly lubricated.
CAMEL Transmission Machinery Factory is a professional supplier,distributor and manufacturer of speed reducers and related accesories. including gear reducers,rotary reducer,worm gearbox, servo-gearbox, planetary gearboxes,planetary gear reducer helical gear reducers,planetary gearbox,right angle gear reducer,gear reduction,gear motors, electrical motors,DC motors, DC gear motor,dc gearedmotors,AC gear motor,AC motors, servo motors,ac servo motor,dc servo motor,servomotor, bearings, gears,spur gear,helical gear,bevel gear,worm gear,planetary gear, couplings, oil seals, belts, chains, etc.If you have any need,please feel free to contact CAMEL:
sales@gear-reducer-worm.com
https://www.gear-reducer-worm.com